24/7 Locksmith Services in St. Louis

Commercial Locksmith

Panic Bar Installation and Repair in University city, MO

A panic bar, or exit device, lets people leave by pushing a bar across the door with no key and no special knowledge. We install, repair and adjust exit devices on commercial doors in St. Louis so they latch securely and release when pushed.

Red steel service door with lever hardware on a brick commercial building

Exit devices and how they latch

Exit devices come in a few main types. A rim device mounts on the door face and its latch projects into a surface strike on the frame, which makes it the most common and the simplest to service. A mortise exit device operates a mortise lock body set inside the door edge. Vertical rod devices latch at the top of the frame and often at the floor too.

Vertical rods are used mostly on pairs of doors with no center mullion. Surface vertical rods run on the face of the door, and concealed vertical rods run inside it. They need the most adjustment, because a rod that is slightly too long or short will stop a door latching or make the bar hard to push. Sagging doors and worn hinges make this worse.

Dogging holds the pushbar down and the latch retracted, so the door works as a simple push and pull during business. It is done with a hex key or a cylinder. Fire-rated openings use fire exit hardware, which has no mechanical dogging because the door must latch. Which doors need which hardware depends on your building and the local authority.

Exit device services

We work on the device, its trim and the parts of the door that affect it.

  • New rim exit device installation
  • Surface and concealed vertical rod adjustment
  • Mortise exit device repair
  • Latch, strike and dogging mechanism repair
  • Outside lever, pull and cylinder trim
  • Rekeying exit device cylinders
  • Exit alarm devices on back doors
  • Mullion and strike alignment on door pairs

Benefits of professional panic bar installation & repair

Questions about panic bar installation & repair? Call 314-314-9909 and talk it through with us.

Doors that release on a push

We check that the bar depresses freely and the latch retracts fully, so the door opens without a second shove or a trick.

Doors that latch behind you

A back door that bounces off its strike is an open door. We adjust latch, strike and closer so it catches as it should.

Repair where repair is sensible

Many faults are a worn latch, a broken spring or a loose end cap. We replace parts when they are available and worth fitting.

Entry control from outside

Outside trim can be a pull only, a keyed cylinder, a lever or an electrified option, depending on who should come in through that door.

Signs an exit device needs attention

The bar is stiff or stays down

A pushbar that sticks, sags or does not spring back usually has a worn mechanism or a bent chassis from heavy use.

The door will not stay latched

Wind or a pull from outside opens it. The latch may not be reaching the strike, or a rod has gone out of adjustment.

The dogging will not hold

The bar keeps popping back up when you try to hold the door unlatched, or the hex key just spins in a stripped fitting.

A change of use or a report

You are fitting out a space, or an inspector has asked for exit hardware on a door. Share the requirement and we will work to it.

How we handle exit device work

We look at the whole opening

Exit device faults are often caused by the door, hinges, closer or threshold. We check those before blaming the bar.

Measured before ordered

Door width, stile width, thickness, handing and any fire label all decide which device fits. We confirm them on site first.

Straight talk about requirements

We tell you what we can do and what your inspector or building owner has to decide, and we follow their direction.

Our panic bar installation & repair process

1

Inspect the door

We operate the device, watch the latch and rods, and check hinges, closer and frame for causes outside the hardware.

2

Explain repair or replace

You hear what has failed, whether parts make sense, and what a new device would involve, with the cost before we begin.

3

Fit and adjust

We install or repair the device, set the strike, adjust rod length where fitted, and mount or rekey the outside trim.

4

Test in use

We push the bar from several points, let the door close on its own repeatedly, and confirm it latches and reopens freely.

Panic Bar Installation & Repair questions

Have a question that is not covered here? Call us at 314-314-9909 and we will answer it directly.

Both release the latch when the bar is pushed. Panic hardware is tested for egress and may have mechanical dogging. Fire exit hardware is also tested for use on fire doors, carries a label saying so, and cannot be mechanically dogged because a fire door has to latch. The door’s rating decides which is needed.

That depends on the building’s use, how many people it holds and what your local authority has adopted, so it is not something we can rule on. Your fire marshal, building department or landlord can tell you. Once you know what is required on which doors, we can supply and fit hardware to match.

Adding chains, padlocks or slide bolts to a required exit door is widely prohibited while a building is occupied, and it creates a real danger if someone forgets to remove them. Ask your fire marshal what applies to you. Better options include a properly latching device, an exit alarm or a guarded outside trim.

On a pair of doors with no fixed post between them, there is nothing in the middle for a rim latch to catch. Vertical rods latch each leaf into the head of the frame and sometimes the floor. A removable mullion is an alternative that lets both leaves use simpler rim devices.

Yes. Devices are available with a built-in exit alarm that sounds when the bar is pushed, with switches that signal a monitoring system, and with electric latch retraction so a card reader can release the door. Which of these suits you depends on the door and on any requirements for that exit.

Free quote

Tell us what you need and we will get back to you

Send a few details about the lock, key or vehicle and where the work is needed. For anything urgent, calling is the fastest way to reach us.

  • Residential, commercial and automotive work
  • We explain your options before any work starts
  • Mobile service across the St. Louis area

Request a free quote

Need a locksmith in St. Louis? Call us now.

Speak with St. Louis Locksmiths about your home, business or vehicle. We will tell you what the job involves and send a technician to you.